MPJA-X60: Oscilloscope probe 60MHz (attenutation x1or x10))

Accessory type: Oscilloscope probe / sensor

MPJA-X60 is a passive high impedance oscilloscope probe designed and calibrated for use on instruments having an input impedance of 1M Ohm shunted by 20pF. However it may be compensated for use with instruments have an input capacitance of 10-50pF. The probe incorporates a two position slide switch in the head which selects attenuation of x1, x10.

Probe technical parameters:

• Attenuation ratio: 1:1, 1:10
• Frequency range: 60MHz
• Input resistance: 1M Ohm / 10M Ohm (1:1, 1:10)
• Input capacitance: 15pF
• Compensation range: 10pF-50pF
• Attenuation ranges: 1:1 , 1:10
• Cable length: 1,2m

CS1002: Oscilloscope probe 250MHz (attenuation x100)

Accessory type: Oscilloscope probe / sensor

CS1002 is a low-input capacitance high voltage oscilloscope probe designed and calibrated for use with instruments having an input impedance of 1 MOhm shunted by 5.5pF. However, it may be compensated for use with instruments having an input capacitance of 10 to 35pF.

Technical specification:

• Attenuation ratio: 100:1
• Frequency range: DC to 250MHz
• Input impedance: 100MOhm || 5.5 pF
• Compensation range: 10pF až 35pF
• Working voltage: 1500Vrms, CAT II
• Cable length: 1,3m

CS1003: Oscilloscope probe 50MHz (attenuation x1000)

Accessory type: Oscilloscope probe / sensor

CS1003 is high-voltage oscilloscope probe designed and calibrated for use with instruments having an input impedance of 1 MOhm shunted by 3pF. However, it may be compensated for use with instruments having an input capacitance of 10 to 35pF.

Technical specification:

• Attenuation Ratio: 1000:1
• Frequency range: 50MHz
• Input impedance: 100MOhm || 3pF
• Compensation range: 5pF až 50pF
• Working Voltage: DC:1.5kV; AC Pulse: 30kV p-p; Sine Wave:10kVrms
• Cable length: 2m

CS1030: Differential oscilloscope probe 25MHz (attenuation x20, x50, x200)

Accessory type: Oscilloscope probe / sensor

CS1030 is an active differential oscilloscope probe with switchable ranges (x20, x50,x 200) designed for making isolated measurements between any two points in a system.

Accessories that are included with the differential probe are:Carry Bag, Instruction Manual, Large Crocodile Clips, Long Grabber Clips, Test leads, BNC-BNC cable, Power supply.

Technical specification:

• Attenuation ranges: 20:1, 50:1, 200:1 (1M Ohm), 40:1 100:1 400:1 (50 Ohm)
• Frequency range: 15MHz (range x20), 25 MHz ( range x50, x200)
• Input impedance: 4 MΩ 1.2 pF (between inputs), 2 MΩ 2.3 pF (between input and ground)
• Max Differential Voltage: 1300V (DC +peak AC)
• Max Voltage to Ground: 1000V (DC +peak AC)
• Safety standard: IEC1010-1 Cat 1. EN61010, UL3111
• Cable length: 2m
• Power supply: One internal 9V PP3 battery or external 6-9V DC

CS1031: Differential oscilloscope probe 50MHz (x100, x200, x500, x1000)

Accessory type: Oscilloscope probe / sensor

The CS1031 is an active differential probe with switchable ranges of attenuation (x100, x200, x500 and x1000) with 50 MHz bandwidth designed for making isolated measurements between any two points in a system.

Accessories that are included with the differential probe are:Carry Bag, Instruction Manual, Large Crocodile Clips, Long Grabber Clips, Test leads, BNC-BNC cable, Power supply.

Technical specification:

• Attenuation ranges: 100:1, 200:1, 500:1, 1000:1 (1M Ohm), 200:1, 400:1, 1000:1, 2000:1 (50 Ohm)
• Frequency range: 25MHz ( range x100), 50 MHz (range x200, x500, x1000)
• Input impedance: 4 MΩ 1.2 pF (between inputs), 2 MΩ 2.3 pF (between input and ground)
• Max Differential Voltage: ±6500V (DC + peak AC)
• Max Voltage to Ground: 6500V (DC + peak AC)
• Safety standard: IEC1010 Cat 1. EN61010, UL3111
• Cable length: 1m
• Power supply: One internal 9V PP3 battery or external 6-9V DC

LACAB0-7: Logic Analyzer Wiring Harness for ELAB-080 device

Accessory type: Cable - wiring

Wiring harness for digital inputs of logic analyzer for ELAB-080 device. Channels CH0-CH7.

Cable length: 0,5m

LACAB8-15: Logic Analyzer Wiring Harness (CH8-CH15)

Accessory type: Cable - wiring

Wiring harness for digital inputs of logic analyzer for ELAB-080 device. Channels CH8-CH15.

Cable length: 0,5m

IOCAB-1: Wire Harness for digital I/O for ELAB-080 device

Accessory type: Cable - wiring

Wiring harness for digital inputs/outputs for ELAB-080 device. Wiring for digital outputs of arbitrary waveform generator, clock generator units, power supply outputs, and external trigger input

Cable length: 0,5m

CABUSB-AB: Interconnecting USB cable (type A-B)

Accessory type: Cable - wiring

Spare interconnecting USB cable to connect device to the host computer. Cable type: A-B male-male.

CABUSB-AB is designed for use with following devices: ELAB-080, CS328A, CS320A.

Cable length: 1.2m

PWELAB220: Power supply adapter for ELAB-080 device, 230V / 50Hz

Accessory type: Other accessories for measuring and testing devices

Spare power supply adapter of ELAB-080 devices designed for 230V/50Hz network. Plug type: EU-continental.

Power supply output voltage: ±16V (400mA) ; +5V (500mA)

PWELAB110: Power supply adapter for ELAB-080 device, 110V / 60Hz

Accessory type: Other accessories for measuring and testing devices

Spare power supply adapter of ELAB-080 devices designed for 230V/50Hz network. Plug type: USA.

Power supply output voltage: ±16V (400mA) ; +5V (500mA)