CS328A technical specifications
Analog inputs and acquisition parameters
| Channels: | 2 |
| Sample rate: | 100MS/sec. for each channel |
| Resolution: | 10 bits (optionally 12 bits or 14 bits) |
| Měmory: | 4M samples (optionaly 8M) |
| Input impedance: | 1MOhm ±2% || 20pF ±3pF |
| Maximum voltage:: | 300Vrms, 420V peak (no damage) (duty cycle <50%, pulse width <100 msec) |
| Input coupling: | DC, AC, GND |
| Acquisition modes: | Single Shot, Triggered, Automatic, Repetitive (High Frequency), Multiple Frame |
| Acquisition rate: | Acquisition rate to PC via USB is 10 Frames/sec. |
| Time delay: (between channels) | 200ps (typical) |
Voltage and time base
| Full Scale Volts Range: | from 20mV to 20V (1x probe) |
| Voltage base sensitivity: | 0.02mV for 20 mV full scale |
| Maximal analog bandwitdh: | 100 MHz, -3dB |
| Lower Frequency limit, AC coupled: | 10Hz (probe 1x), 1Hz (probe 10x) |
| Rise time at the BNC: | <3ns (typical) |
| Peak detect response: | captures all pulses >10ns in duration |
| Sample Rate Range: | from 1500 samples/sec. to 100M samples/sec |
| Time base range: | from 1ns/div to 5s/div in 1,2,5 sequence |
| Sample Clock jitter: | 1 ps rms (typical) |
| Record Length: | 1024 – 2 000 000 samples for each channel |
| Waveform interpolation: | Sin(x)/x |
| Captured Sample window duration: | 1usec – 40msec with 10ns resolution 40msec – 42.9 secs with 10ns - 10usec resolution. (Lower sample rates are used for smaller capture buffer sizes) |
Trigger possibilities
| Trigger Sensitivity, Edge Triggered: | Analog Channels: 0.2 Div from DC to 50 MHz Analog Hardware Trigger: 0.5 div from DC to 200 MHz External Trigger: 50 mV from DC to 100 MHz |
| Trigger modes: | Edge, Window, Pulse Duration |
| Trigger filtering: | Noise reject, HF reject, LF reject |
| Trigger level range: | Internal: defined by scope graph External: ±20V in 40 mV increments |
| Trigger holdoff range: | 0 to 42.9 secs with 10ns resolution |
Signal Generator Plug-in CS700 (optional extension)
| Generated functions: | Sine, Square or Triangle output signals, possibility of sweep and modulation funtions |
| Generation Method: | Direct Digital Synthesis |
| Output Sampling Rate: | 50MS/sec. |
| Frequency Range: | Sine, Square: 0.2 Hz to 10 MHz; Triangle: 0.2 to 1 MHz |
| Output Voltage Range: | from 100mV to 5VPEAK-PEAK including DC offset with 10mV resolution |
| Output Voltage Offset Range: | -4V to +4V with 10mV resolution |
| Output Impedance: | 50 Ohm |
| Signal to Noise Ratio: | -60 dBc (typical) |
| Total Harmonic Distortion: | for frequencies from 0 to 1 MHz: < -65 dBc: ; for frequencies >1MHz: < -35 dBc |
General specifications
| Probe Compensator Output: | 3V, 1kHz into >100k Ohm load |
| Power supply: | 6-20V DC |
| Power Consumption: | 5W |
| Temperature range: | Operating: 0°C to +40°C Storage: -20°C to +60°C |
| Dimensions: | 35mmx153mmx195mm (HeightxWidthxDepth) |
| Minimal PC requirements: | PC with Pentium II processor memory 64MB at least free USB port |
| Package content: | CS320A device 2 oscilloscope probes 250MHz (CS1001) Power supply adaptor 230V/50Hz 2 Digital probe pods (CS1004,CS1005) Interconnecting USB cable Printed documention CD with software, documentation, etc. |
Complete detail technical specification for Cleverscope CS320A
can be downloaded in PDF format
HERE
Digitálal inputs
| Channels: | 8 |
| Input Impednce: | 100k Ohm ±2% || 10pF ±2 pF |
| Input Range: | od -16 do + 20V |
| Threshold range: | 0V to 8V in 10 mV steps |
| Threshold sensitivity: | 100 mV |
| Sample Rate: | 100MS/sec |
